Written by Rick Kovac, COO of Golden Lighting
The takeaway: To uplight an exterior house wall without glare or spill, light only one or two features that deserve it, graze textured walls and wash smooth ones, keep every beam on the building with shielded, carefully aimed fixtures, and hold the color at 3000K or warmer.
Key takeaways:
- Pick one brightest feature, usually the entry, and let the rest of the facade glow softly or stay dark. A house lit edge to edge looks commercial, not welcoming.
- Graze stone, brick and rough stucco from close to the wall to bring out texture. Wash smooth siding and painted walls with a softer, wider spread.
- Glare is a visible bright source. Shield it, aim it at the wall rather than at people or the sky, and check the result from the street and from your neighbor's side.
- Outdoors, stay at 3000K or lower, never 4000K or cooler. Every fixture must be rated for its location, and line-voltage wiring is a job for a licensed electrician.
A house can look wonderful at noon and disappear at nine. The stonework goes flat, the entry wall reads as a blank plane, and the one porch bulb becomes a bright spot that faces the street. More light rarely fixes that. Better-placed light does.
This guide is about the walls themselves: which ones to light, how to light them, and how to keep the light where you put it. For trees and plantings, see our guide to spotlights for trees. For the yard as a whole, start with landscape lighting ideas.
Light less of the house than you think
The most common mistake with facade lighting is treating every wall, column and window bay as a candidate. Uplights work best as deliberate accents, not blanket coverage. Soft downlight from eaves and trees does most of the ambient work in a good exterior scheme, and uplights are saved for the few features that earn them.
- Choose one destination. At the front of a house, that is almost always the entry. It should read as the brightest part of the scene.
- Pick one or two supporting features. A stone chimney, a pair of columns or a textured wall beside the door. These step down in brightness from the entry.
- Leave the rest in soft shadow. Garage doors, blank side walls and long runs of siding don't need their own light. Darkness gives the lit features their shape.
- Light the steps separately. Architectural accents are not a substitute for step and walkway light. Every grade change people walk on should show a readable tread edge.
Our rule: let the house glow, don't blast it. If the facade is the brightest thing on the street, it's too bright.
Keep the facade softer than its focal point. A uniformly floodlit front wall flattens the architecture and fights the entry for attention. Our guide to exterior home lighting covers how the entry, porch and path layers fit together around these accents.
Graze or wash: match the technique to the wall
How you aim the light matters as much as what you light. Light that skims across a rough surface throws small shadows that reveal its texture. Light spread evenly over a smooth surface hides imperfections and gives a calm glow.
| Wall surface | Technique | How to set it up |
|---|---|---|
| Natural stone, brick, fieldstone | Graze | Set the fixture close to the base of the wall and aim it up the face, so the light rakes across the texture. |
| Rough stucco, textured block | Graze, gently | Same close setup, lower output. The goal is relief, not a hot stripe at the bottom of the wall. |
| Smooth stucco, painted siding, fiber cement | Wash | Move the fixture farther from the wall with a wider spread. Grazing a smooth wall exaggerates every seam and patch. |
| Columns and pilasters | Narrow accent | One tight beam per column, aimed so it ends on the column rather than continuing past the top. |
| Warm materials (wood, warm stone) | Graze or wash, warmer light | Lean toward 2700K on warm materials. It flatters wood and warm stone. |
One placement rule worth remembering: keep wall washers and uplights at least 3 feet from the side of any doorway, so the upward beam doesn't shine into the eyes of someone walking through. That guidance comes from the American Lighting Association's residential lighting training manual.
Stop glare and spill before they start
Glare and spill are two different problems. Glare is seeing the bright source itself. Spill, or light trespass, is light landing where it wasn't meant to go: a neighbor's bedroom window, the street or the open sky. Good exterior lighting shows the effect and hides the fixture.
- Aim at the wall, not past it. Tilt each uplight so its beam finishes on the building. Rooflines and column tops are where light most often escapes into the sky.
- Shield every source. Use fixtures with a recessed lamp, a glare shield, a snoot or a louver, with a dark interior. From normal viewpoints you should see a dark fixture and a lit wall, never a bright point.
- Check the sightlines. Look at each fixture from the front walk, the driveway, the porch seat and the sidewalk. If you can see the lamp from where people stand or sit, re-aim or shield it.
- Walk to the property line. Stand where your neighbors would and look back. If light reaches their windows or yard, pull it back.
- Use as little as you need. Turn the output down until the detail you want starts to fade, then raise it just enough to bring it back. Judge the wall, not the fixture.
DarkSky International frames responsible outdoor lighting as five questions: does each light have a clear purpose, is it directed only where it's needed, is it brighter than it needs to be, is it on all night, and is it as warm as it can be. Their home outdoor lighting guidance is a useful checklist before you buy anything.
The mark of a well-lit house is that you notice the stone, not the lights.
Color temperature and controls
- Color temperature: 3000K or warmer for every exterior fixture, including uplights. Use about 3000K where light falls on plantings and about 2700K on warm materials and decorative fixtures. Cool white at 4000K and above reads harsh and institutional on a home. DarkSky's guidance also recommends 3000K or lower.
- Match the whole elevation. A warm wall accent beside a cooler porch light makes the scheme look pieced together. Set every fixture on the facade to the same color.
- Color rendering: choose CRI 90 or higher where you can, so brick, stone and paint colors look like themselves after dark. Here's what CRI means.
- Controls: put architectural accents on a timer, an astronomical time clock or a smart schedule so they switch off when the evening is over. Keep them on a separate circuit or zone from security and step lighting, which may need to behave differently.
- Dimming: dimming lets you tune each feature against the others, but it is not a substitute for turning an accent off when nobody is enjoying it.
Ratings, wiring and safety
- Match the rating to the exposure. Under the National Electrical Code (NEC 410.10(A)), fixtures in wet locations must be marked suitable for wet locations, and damp locations need at least a damp rating. An exposed wall or a fixture in the ground is a wet location. A covered porch ceiling is usually damp. Our guides to damp-rated vs. wet-rated fixtures and wet-rated outdoor lighting explain the difference.
- Look for a listing mark. A UL or ETL mark tells you the fixture was tested for the location it's sold for. See UL vs. ETL for what that testing covers.
- Low-voltage landscape systems: NEC Article 411 covers lighting systems that run at 30 volts or less, and requires them to be listed. Follow the system maker's instructions for the transformer, cable and burial depth. Long runs lose voltage, which can make the far fixtures dimmer and slightly off-color, so plan runs and transformer placement with that in mind.
- Outdoor receptacles: the NEC (210.8(A)(3)) requires GFCI protection for outdoor receptacles at homes. If a transformer plugs into an outdoor outlet, that outlet should be GFCI-protected.
- Hire a licensed electrician for any line-voltage (120-volt) work: new circuits, wall-mounted fixtures, junction boxes or anything you're unsure of. Turn off the breaker, not just the switch, before touching any wiring.
When a wall light does the job better
Not every facade needs ground-mounted uplights. Around an entry or a garage, a well-chosen outdoor wall light can wash the wall above and below itself, light the door zone and keep the source out of sight, with one wire and no stakes in the garden bed.
- Up/down wall lights throw light both ways along the wall, which gives a smooth wall a soft wash and frames a doorway.
- Downlight-only, fully shielded wall lights keep all the light below the fixture. They're the most neighbor-friendly choice next to bedroom windows or close property lines.
- Pathways: if your walk still needs light after the entry and borrowed light are in place, keep path lights few, low and shielded. Our guide to contemporary pathway lighting shows how.
For more wall-light options, see our best outdoor wall lights guide and outdoor house lighting.
Shop this guide
- Stela Integrated LED 16in Outdoor Wall in Gray Travertine: up/down light, wet rated, 3000K, CRI 90, 750 lumens. A soft wash beside an entry door.
- Stela Integrated LED 24in Outdoor Wall in White Travertine: the larger up/down version, wet rated, 3000K, CRI 90, 1,820 lumens, for a wider or taller wall.
- Stela Integrated LED 9in Outdoor Wall in Gray Travertine: the compact version, wet rated, 3000K, CRI 90, 530 lumens, for a side door or a narrow pier.
- Aethera Integrated LED Wall Sconce in Grey Cement: downlight only and dark-sky friendly, wet rated, CRI 90, 310 lumens, 8.5 inches wide. Its color is selectable; set it to 3000K outdoors.
Light the one or two things that make your house yours, keep the beams on the building, and keep it warm. Browse outdoor wall lighting, or find a Golden Lighting retailer to see the finishes in person.
— seen a lot of light fixtures in 80+ countries. Still learning what actually works in a home.















Share:
Hallway Wall Ideas: How to Decorate and Light a Hallway Wall